Remington Electric Shaver DA 57 User Guide

Use this shaver only for its intended use as  
described in this manual. Do not use attach-  
ments not recommended by Remington.  
Keep the cord away from heated surfaces.  
Never operate this shaver if it has a damaged  
cord or if it is not working properly, if it has  
been dropped or damaged, or dropped into  
water. Return the shaver to a service center  
for examination and repair.  
IMPORTANT SAFETY  
INSTRUCTIONS  
®
How to get a great shave  
from your Remington®  
MicroScreen® 2 Shaver  
When using an electrical shaver, basic precautions  
should always be observed, including the following.  
Read all instructions before using this shaver.  
Thank you for buying this premium  
shaver from Remington®.  
Never drop or insert any object into any open-  
DANGER  
ing.  
Inside you'll find tips on using and  
caring for your shaver to get the  
best shave possible.  
To reduce the risk of electric shock:  
Do not use outdoors or operate where aerosol  
(spray) products are being used or where oxy-  
gen is being administered.  
Do not use this shaver with a damaged or  
broken cutter or head, as facial injury may  
occur.  
Always attach plug to shaver, then to outlet.  
To disconnect, turn all controls to “Off,” then  
remove plug from outlet, then detach power  
cord from the shaver for storage.  
Always store your shaver and cord in a mois-  
ture-free area. Make sure your cord is discon-  
nected from the shaver.  
Do not reach for a shaver that has fallen into  
water. Unplug immediately.  
Do not use while bathing or in a shower.  
Do not place or store shaver where it can fall  
or be pulled into a tub or sink. Do not place  
in or drop into water or other liquid.  
Except when charging, always unplug this  
shaver from the electrical outlet immediately  
after using.  
Unplug this shaver before cleaning.  
WARNING  
To prevent possible damage to the cord, do  
To reduce the risk of burns, fire, electric shock,  
or injury to persons:  
not wrap cord around the shaver.  
Never put the shaver in direct sunlight or store  
in pouch at a temperature above 140° F.  
“Household Use Only”.  
Model DA-757  
(LCD Display)  
Model Only  
A shaver should never be left unattended when  
plugged in, except when charging your  
rechargeable shaver.  
Model DA-57  
(no LED)  
Model DA-107  
(no LED)  
Model DA-307  
Model DA-325  
Close supervision is necessary when this  
shaver is used by, on, or near children or  
invalids.  
SAVE THESE  
INSTRUCTIONS  
Model DA-407  
 
Model DA-307 and DA-325 With the shaver unplugged,press in on the  
Switch Lock and slide the ON/OFF button upward to turn ON.Note that this  
shaver is designed only to operate from its batteries; it must be charged  
before using.  
Model DA-407,and DA-757 These shavers can be powered from either  
the cord or the battery. To shave using the battery, make sure that the  
shaver has been charged. To shave using the cord,connect cord to shaver  
and then to electric outlet.Press in on the Switch Lock and slide the ON/OFF  
button upward to turn ON.  
Every six months, lubricate the trimmer  
teeth by applying a drop of light machine  
oil one-third and two-thirds of the way along  
the blade. Using your finger tip, spread the  
oil along the teeth, and run the trimmer for a  
few seconds.  
Removing the Headguard  
Before operating your  
MicroScreen® 2 Shaver, remove  
the Headguard, which protects  
the Foils and Cutter Assembly.  
It is important to remove the  
Headguard correctly to avoid  
Replacing Foils and Cutters  
damaging the clips that hold  
Because they are subject to daily use, the cutters and foils of your  
Remington® MicroScreen® 2 Shaver will wear and eventually require  
replacement to maintain a close, comfortable shave. Depending on your  
shaving technique and habits, the foils will usually last six months; the  
cutters, one year. Model DA-757 has a foil replacement indicator.  
The foil icon on the LCD display will flash when the foil is due for  
replacement. Some signs that your foils and cutters need replacing are:  
it firmly to the shaver.  
Trouble Shooting  
Press lightly on the top of the Headguard.  
If your DA-407, 757 shaver battery is completely discharged or the shaver has  
not been used for an extended period of time, the shaver may not start when oper-  
ated using the cord. If this condition occurs, charge the shaver for approximately  
five minutes before shaving.  
Lift the lower rear edge.  
Pull the Headguard away from the shaver.  
Operation  
Use of a shaver at voltages other than the ones  
specified below will damage it and void the warranty.  
Model DA-57, DA-107 - Corded Shavers 120 Volts A.C.  
Model DA-307, DA-325 - Rechargeable Shaver  
World-wide A.C.voltage:105-130 Volts A.C.  
Your DA-407, 757 cord/cordless shaver should not be used strictly as a cord-  
operated shaver, as continued cord only use will result in reduction of battery life.  
In order to preserve the life of the batteries,they should be fully discharged every  
six months and then fully charged for 24 hours.  
Irritation. As foils get worn, you may notice your skin feeling  
sensitive after a shave, particularly when you apply aftershave.  
Pulling. As cutters wear, your shave may not feel as close, and you  
may feel your shaver is pulling at your whiskers.  
Wear-through. You may notice that the cutters have worn through  
the foil.  
at 60 Hz,and 105-240 Volts,A.C. at 50 Hz.  
Model DA-407 - Cord/Cordless Shaver World-wide A.C.  
voltage:100-240 Volts A.C.,50-60 Hz.  
Model DA-757 - Cord/Cordless Shaver With LCD Display  
World-wide A.C.voltage:100-240 Volts A.C.,50-60 Hz.  
Battery Removal  
(Cord/Cordless and Cordless  
Rechargeable Models Only)  
To order replacement foils and cutters, call 1-800-736-4648.  
When your rechargeable shaver  
reaches the end of its useful life, the  
batteries must be removed from the shaver and be recycled  
or disposed of properly in accordance with your local and state  
requirements.  
The following procedure should be followed  
for battery removal:  
• To avoid a possible electrical shock hazard,unplug cord  
from electrical outlet and shaver.  
• Remove the head assembly by pushing in on the  
head assembly release buttons.  
• Remove the two screws on the upper back side of the  
shaver.  
• Pull or pry the shaver halves apart.  
• Pull out the motor and frame assembl y.  
• Pull or pry the batteries outward from the shaver’s  
circuit board.  
• Pull and twist the batteries to break the wire connections.  
• CAUTION:Do not put in fire or mutilate your batteries when  
disposing as they may burst or release toxic materials.Do  
not short circuit as it may cause burns.Dispose of properly  
in accordance with your local and state requirements.  
To prevent inadvertent damage to the Foils and Cutter Assembly,  
do not attempt to remove them unless you are replacing them. To  
remove the old foil and cutters follow the instructions that come with the  
foil and cutter replacement package. It's always a good idea to replace  
the foils when you replace the Cutter Assembly.  
Charging  
Charge your shaver 24 hours before initial use.  
Make sure the ON/OFF button is set to OFF (with  
“O” visible). Connect the cord to the shaver and then  
to the electric outlet.  
Model DA-307, DA-325,and DA-407 The Green indicator  
light will glow indicating that the shaver is charging.  
The shaver will be completely recharged in 14-16 hours.  
The red indicator light in the DA-325 model will glow  
when the shaver needs to be recharged.  
Model DA-757 This shaver has an LCD display. The bars  
on the display give the % of battery power left in your  
shaver. The plug icon will flash when your shaver needs  
to be recharged. There is also a foil replacement indica-  
tor. The foil icon on the display will flash when the foil is  
due for replacement. The one hour quick charge fea-  
ture in this model gives up to 60 minutes of cordless  
shaving time. A 5 minute quick charge gives enough  
shaving time for one shave  
To Replace a Cutter Assembly That is Removed  
Unintentionally:  
Hold the assembly in the middle of the "T."  
Gently place the forked legs into the open-  
ing at the top of the oscillator tips.  
Do not push downward on the ends of the  
cutters, as you may bend the cutter, reducing  
its ability to operate smoothly.  
Do not remove cutters from the plastic  
pieces to which they are attached, as you may  
damage the assembly.  
CAUTION: THESE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR DISPOSED IN  
ACCORDANCE WITH STATE AND LOCAL REGULATIONS. Do not burn or mutilate, as they  
may burst or release toxic materials. Do not short-circuit, as it may cause burns.  
To Shave  
Model DA-57,and DA-107 Connect cord to shaver and then  
to electric outlet.Slide the ON/OFF button upward to turn ON  
.
 
®
Headguard  
Warranty service must be performed by a Remington Company-  
owned Service Center or Authorized Service Dealer and damage or  
loss of any kind resulting from servicing by any other person is not  
covered under warranty. Enclosed is a listing of Company-owned  
Service Centers. Authorized Service Center Dealers may be found  
in the yellow pages of your directory. If you wish, you may mail  
the product, postpaid,to Remington Products Company, 60 Main  
Street,Bridgeport, CT 06604 Attention:Service Department.  
Remington Money-Back Offer  
You have just bought one of the finest  
shavers available today. If for any reason  
within 30 days from when you purchased  
®
®
your Remington MicroScreen 2 Shaver,  
you are not satisfied and would like a  
refund, just return your shaver, together  
with the sales receipt, to the retailer from  
whom you purchased it. Remington will  
reimburse all retailers who accept shavers  
within 30 days of purchase. If you have  
any questions regarding this money-back  
guarantee, please call 1-800-736-4648.  
Dual Flexible  
MicroScreen® Foil  
Head  
Assembly  
U.S. Warranty Service  
ON/OFF Switch Lock  
(DA-307, DA-325,  
DA-407)  
In the United States, service is provided  
by our Company-owned Service Centers  
and over 300 Authorized Service Dealers.  
The addresses of our Company-owned  
Service Centers are enclosed. For the  
address of your nearest Authorized Service  
Dealer, please consult the Yellow Pages  
under “Shaver - Electric - Repair.” If you  
wish, you may mail the product, postpaid,  
to Remington Products Company, 60 Main  
Street, Bridgeport, CT 06604, Attention:  
Service Department.  
ON/OFF Switch  
Head  
Easy-View Trimmer  
Rear of Shaver  
Assembly  
Release  
Button  
(Both sides)  
Full One-Year Warranty  
Remington warrants that your product, except as noted below, is,  
on date of purchase, free from defect in material and workmanship.  
Remington will correct any such defect without charge if you return  
the complete product either in person or by mail, postage paid, to a  
Remington Company-owned Service Center or Authorized Service  
Dealer within one year after date of purchase.  
Charging  
Indicator  
Light  
(DA-307,  
DA-325,  
DA-407)  
Do not return the product to the retailer from whom the product  
was purchased.  
International Warranty Service  
Foil  
Gauge  
DA-757  
Service under the Remington warranty can  
be obtained outside the United States by  
Remington-Authorized Distributors and  
Service Dealers. Please consult your local  
telephone directory for the nearest location.  
Low Battery  
Indicator Light  
(not shown)(DA-325)  
This warranty does not cover damage by accident, misuse,abuse or  
by affixing an unauthorized accessory or alteration to the product, or  
by connection of the product to any but the specific current and volt-  
age indicated in an accompanying instruction booklet, or by any  
other conditions beyond our control. REMINGTON SHALL NOT BE  
RESPONSIBLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL  
DAMAGES.  
Cord Inlet  
Remington MicroScreen® 2 Models  
Which model is yours?  
For questions or comments, please write:  
Remington Products Company, L.L.C.  
P.O. Box 1536,  
IN ADDITION,THIS WARRANTY DOES NOT COVER THE FLEXIBLE  
SCREEN ASSEMBLY ON OUR FOIL TYPE SHAVERS.  
DA-57,  
DA-107  
Corded Shavers,  
120 Volts A.C.  
Horsham,PA 19044-6536  
Attention:Consumer Affairs  
ALL IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED  
WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE LIMITED IN  
DURATION TO ONE YEAR FROM DATE OF ORIGINAL PURCHASE.  
DA-307,  
DA-325  
Rechargeable Shaver - World-wide A.C.  
105-130 Volts A.C. at 60 Hz ,and 105-240 Volts,  
A.C. at 50 Hz.  
Questions or Comments: Please call 1-800-736-4648.  
This warranty gives you specific legal rights, and you may also have  
other rights that vary from state to state. Some states do not allow  
the exclusion limitation of incidental or consequential damages or  
limitations on how long an implied warranty lasts, so that the above  
limitations and exclusions may not apply to you.  
DA-407  
DA-757  
Cord/Cordless Shaver - World-wide A.C.  
voltage:100-240 Volts A.C.,50-60 Hz  
Remington,MicroScreen and  
ShaverSaver are trademarks of  
Remington Corporation,L.L.C.  
Cord/Cordless Shaver with LCD Display  
World-wide A.C.voltage:100-240 Volts A.C.,  
50-60 Hz  
P R O D U C T S C O M PA N Y, L . L . C .  
No responsibility, obligation,or liability is assumed for the installation  
or maintenance of this product.  
© 1999 RPC, L.L.C.Rev. 3/99  
Part No. 12554  
60 Main Street Bridgeport, CT 06604  
U.S. Patent Design #362, 739  
Canadian Design Patent 77, 681  
 

RayTek Thermometer MX Series User Guide
RCA Camcorder EZ5000 User Guide
Renesas Stereo Amplifier M65881AFP User Guide
RIDGID Battery Charger R9213 User Guide
Ryobi Saw OJ1802 User Guide
Samsung Range FTQ307NWGX User Guide
Samsung Vacuum Cleaner SU 8500 User Guide
Sanyo Digital Camera VCC HD4000 User Guide
Sears Lawn Mower 91725148 User Guide
Sennheiser Headphones HD 438 User Guide